-
شماره ركورد
23302
-
پديد آورنده
احسان شكراله زاده
-
عنوان
طراحي و ساخت پراب اندازه گيري ميدانهاي الكترومغناطيسي مبتني بر PCB
-
مقطع تحصيلي
كارشناسي ارشد
-
رشته تحصيلي
مخابرات ميدان و موج
-
سال تحصيل
96-99
-
تاريخ دفاع
1399/8/27
-
استاد راهنما
دكتر علي عبدلعالي
-
استاد مشاور
دكتر مجيد طيراني
-
دانشكده
برق
-
چكيده
امروزه اندازه¬گيري و ثبت ميدان¬هاي اطراف دستگاه¬ها و مدارات الكترونيكي از هر زمان ديگر اهميت بيشازپيش پيداكرده است چراكه با پيشرفت فنّاوري و فشرده شدن هر چه بيشتر اين مدارات و نياز به مطابقت با استانداردهاي EMC، كه ضامن عملكرد درست مي¬باشد، اين كار اهميت زيادي پيدا كرده اند. در اين پايان¬نامه علاوه بر طراحي دو پراب ميدان نزديك براي ميدان الكتريكي و ميدان مغناطيسي يك ساختار از تركيب اين دو پراب ارائه شده است كه در مواردي كه اندازه¬گيري هر دو نوع ميدان¬ها مطلوب است زمان اندازه¬گيري و جاروب مكاني را به نصف كاهش مي¬دهد.در پايان نتايج تست عملي در مقايسه با نتايج شبيه سازي آورده شده است كه حاكي از كارايي اين طرح مي باشد.
براي انجام اندازه گيري هاي مختلفي در حوزه ي مخابرات ميدان نياز به دانستن مقادير ميدان ها داريم ، از جمله مواردي كه نياز به ابزاري براي اين كار وجود دارد ، اندازه گيري هاي ميدان نزديك ، اندازه گيري هايEMC ، EMI اندازه¬گيري هاي مربوط به تست هاي استاندارد حد مجاز تشعشع يا هر اندازه گيري ديگري كه نياز به دانستن مقادير دامنه يا فاز ميدانهاي الكترومغناطيسي در يك نقطه است ، مي باشد. پراب ها انواع مختلفي دارند ، پراب هاي EMC يكي از انواع آن است كه نقش جدا سازي يك مولفه ي ميدان در نزديكي يك برد مدار چاپي و رساندن اطلاعاتي از دامنه يا فاز آن به دستگاه هاي گيرنده است .
هدف نهايي پروژه طراحي و ساخت يك مجموعه پراب EMC براي اندازه گيري ميدان الكتريكي و مغناطيسي با مشخصات زير مي¬باشد:
پراب هايEMC : فركانس كاري از 0.1 تا 6گيگاهرتز، ايزولاسيون پلاريزاسيون ها به اندازه ي20 dB،
سطح تابع تبديل بهتر از dB 35- ،رزولوشن فضايي 3 ميليمتر
-
تاريخ ورود اطلاعات
1399/12/13
-
عنوان به انگليسي
Design and implementation of a PCB based probe for EM field measurements
-
تاريخ بهره برداري
11/18/2021 12:00:00 AM
-
دانشجوي وارد كننده اطلاعات
احسان شكراله زاده
-
چكيده به لاتين
One of the key components in evaluating EMC Compliance/pre-compliance is the field Probe which can be used for field mapping, radiated immunity test, radiated susceptibly test, circuit radiation level evaluation, etc. field probe measures the desired field component by means of transforming a single field component, to a measurable entity which is usually an RF voltage fed to a microwave detector, while suppressing the other components to generate a voltage in the output. The most common types of probes, used in EMC tests are loop shaped sensors that measure transverse magnetic field component, and sensors similar to monopole/dipole antennas that measure parallel and transverse electrical components respectively .The basic method for which these kinds of probes are often utilized, is to track radiation sources on PCBs, systems and structures as a handheld device which is usually connected to a RF oscillator/Spectrum analyzer. This enables an experienced EMC engineer to evaluate device under test for faults in design or implantation and perform an EMC pre compliance check.
Off-shelf probes come in sets to cover the entire frequency band of interest and field component types .Wide-band magnetic field probes with multilayer structures based on coplanar waveguide are developed to address this issue. LTCC based probe in has high bandwidth and better spatial resolution but the structure is too complex and very expensive to implement. To further reduce the complexity and cost of such structures in this paper, a magnetic probe with novel shielding structure with a 2 layer structure is designed, along with an electrical probe which both have the same bandwidth suitable to be used with an inexpensive SDR and utilize its full available bandwidth. Both these probes are connected to a RF switch that can select output of which probe is connected to the amplifier that comes after them .these two probes and the RF switch and a cascaded amplifier are all integrated in a single package. They are placed in such a way to accommodate easy scanning in all sorts of the applications that require both or one type of field component data and even make the scanning time half as much, Because two field components can be measured in each position using the probe Having a dipole to measure the transverse electrical field in the structure also enables this setup to measure the data required to perform all kinds of different measurements commonly done today.
-
كليدواژه هاي فارسي
پراب الكتريكي , پراب مغناطيسي , پراب EMC , اسكن PCB
-
كليدواژه هاي لاتين
Electrical Probes , Magnetic Probes , Field Probes , EMC probes
-
لينک به اين مدرک :